"नये भारत का नया Tender Portal"
Providing Laying Spreading And Compacting Specified Graded Sand, Gravel (crushed Stone) As Per Table 400-1,400-2 Or Any Other Course Material As Per Design Mix, As Per Cbr In Sub Base Course Including Premixing The Material At Omc In Wet Mix Plant, Carriage Of Mixed Material Spreading In Uniform Layers With Motor Grader F.e Loader On A Prepared Base And Compacting With Vibratory Roller To Achieve Desired Density (as Per I.s.2720) Including All Material, Labor, Machinery, Lighting Guarding, Barricading And Maintenance Of Diversion Complete.[morth Specification : Clause 401]. By Mechanical Means. For Grading-ii Material Construction Of Dry Lean Cement Concrete Sub- Base Over A Prepared Sub-grade With Coarse And Fine Aggregate Conforming To Is: 383, The Size Of Coarse Aggregate Not Exceeding 25 Mm, Aggregate Cement Ratio Not To Exceed 15:1, Aggregate Gradation After Blending To Be As Per Table 600-1, Cement Content Not To Be Less Than 150 Kg/ Cum, Optimum Moisture Content To Be Determined During Trial Length Construction, Concrete Strength Not To Be Less Than 10 Mpa At 7 Days, Mixed In A Batching Plant, Transported To Site, Laid With A Paver With Electronic Sensor, Compacting With 8-10 Tonnes Vibratory Roller, Finishing And Curing. Construction Of Un-reinforced , Plain Cement Concrete Pavement M30 (grade), Thickness As Per Design, Over A Prepared Sub Base, With 43/53 Grade Cement As Per Clause 602, Coarse And Fine Aggregates Conforming To Is:383, Maximum Size Of Coarse Aggregate Not Exceeding 31.5 Mm, Mixed In A In Fully Automatic Batching Plant And Transported To Site In Transit Mixer For Having Continuous Agitated Mixer, Manufactured As Per Approved Mix Design Including Pumping Of R.m.c. From Transit Mixer To Site Of Laying , With All Lead And Lift Including Cost Of Admixtures In Recommended Portion As Per Is 9103 To Accelerate/ Retard Setting Of Concrete, Improve Workability Without Impairing Strength And Durability As Per Direction Of Engineer In Charge Laid With A Fixed Form Paver (laying And Fixing Of 150 Micron Thick Polythene Film And Finished In Continuous Operation Including Provision Of Contraction And Expansion, Construction Joints, Applying Debonding Strips, Primer, Sealant Near Approaches To Bridge/culvert And Construction Joints, Admixtures As Approved, Curing Of Concrete Slabs For 14-days Using Water Finishing To Lines And Grade As Per Drawing And Morth Specification Clause 602 Including Vaccum Dewatering Process With All Required Equipments (dowel Bars Will Be Paid Seprately). Providing And Fixing Of Dowel Bars Of Mild Steel Confirming To Is : 432 Of Specified Length And Diameters As Per Morth Specification Irc 15 & 58 Including Cutting, Placing In Position Across Transverse Joint With Proper Spacing, Providing With Pvc Sleeve Complete As Per Drawing, Technical Specification And As Per Direction Of The Engineer-in-charge. Construction Of Embankment With Approved Material Obtained From Borrow Pits With A Lift Upto 1.5 M, Transporting To Site, Spreading, Grading To Required Slope And Compacting To Meet Requirement Of Tables 300-1 And 300-2 With A Lead Upto 50 M As Per Morth Specification Clause 305.3 Supply & Fixing Of Flood Gauge (water Gauge) As Per I.r.c. 67 Standard 200 Cm Long Fixed On Angle Iron Posts 50x50x6 Mm, 2.6 M Long Providing And Fixing Of Retro-reflectorised Cautionary, Mandatory And Informatory Sign As Per Irc:67 Made Of Encapsulated Lens Type Reflective Sheeting Vide Clause 801.3.1 Fixed Over Aluminium Sheeting, 1.5 Mm Thick Supported On A Mild Steel Angle Iron Post 75 Mm X 75 Mm X 6 Mm Firmly Fixed To The Ground By Means Of Properly Designed Foundation With M15 Grade Cement Concrete 450 Mm X 450 Mm X 600 Mm, 600 Mm Below Ground Level As Per Drawings And Morth Specification Clause 801 800 Mm X 600 Mm Rectangular Painting Two Coats Including Primer Coat After Filling The Surface With Synthetic Enamel Paint In All Shades On New, Plastered / Concrete Surfaces As Per Drawing And Morth Specification Clause 801 Excavation For Structures Earthwork In Excavation For Structures As Per Drawing And Morth Specifications Clause 304.1 Including Setting Out, Construction Of Shoring And Bracing, Removal Of Stumps And Other Deleterious Material And Disposal Upto A Lead Of 50 M, Dressing Of Sides And Bottom And Backfilling In Trenches With Excavated Suitable Material. Ordinary Soil Upto 3 M Depth Providing Concrete For Plain/reinforced Concrete In Open Foundations Complete As Per Drawings And Morth Specifications Clause 1702, 1703, 2102 & 2104 P.c.c Grade M 10 Nominal Mix 1:3:6 Providing Concrete For Plain/reinforced Concrete In Open Foundations Complete As Per Drawings And Morth Specifications Clause 1702, 1703, 2102 & 2104 R.c.c Grade M 20 Supplying, Fitting And Placing Hysd Bar Reinforcement In Foundation Complete As Per Drawings And Morth Specifications Clauses 1009,1600 And 2102 Chhabra Jharkheri Mandkho Km. 3/400
Excavation For Structures Earthwork In Excavation For Structures As Per Drawing And Morth Specifications Clause 304.1 Including Setting Out, Construction Of Shoring And Bracing, Removal Of Stumps And Other Deleterious Material And Disposal Upto A Lead Of 50 M, Dressing Of Sides And Bottom And Backfilling In Trenches With Excavated Suitable Material. Ordinary Soil Upto 3 M Depth Providing Concrete For Plain/reinforced Concrete In Open Foundations Complete As Per Drawings And Morth Specifications Clause 1702, 1703, 2102 & 2104 P.c.c Grade M 10 Nominal Mix 1:3:6 Providing Concrete For Plain/reinforced Concrete In Open Foundations Complete As Per Drawings And Morth Specifications Clause 1702, 1703, 2102 & 2104 R.c.c Grade M 20 Supplying, Fitting And Placing Hysd Bar Reinforcement In Foundation Complete As Per Drawings And Morth Specifications Clauses 1009,1600 And 2102 Plain/reinforced Cement Concrete In Substructure Complete As Per Drawings And Morth Specification Clauses 1700 And 2200 For Height Upto 5 M R.c.c Grade M 20 Plain/reinforced Cement Concrete In Substructure Complete As Per Drawings And Morth Specification Clauses 1700 And 2200 For Height Upto 5 M R.c.c. Grade M 25 Supplying, Fitting And Placing Hysd Bar Reinforcement (fe 415) In Substructrue Complete As Per Drawings And Morth Specification Clauses 1009,1600 & 2202 Providing Weepholes In Brick Masonry/stone Masonry, Plain/reinforced Concrete Abutment, Wing Wall, Return Wall With 100 Mm Dia Ac Pipe Extending Through The Full Width Of The Structures With Slope Of 1(v):20(h) Towards Drawing Face Complete As Per Drawing And Morth Specification Clauses 1409, 2204.4, 2206.4 & 2706 Providing And Laying Reinforced Cement Concrete In Superstructure As Per Drawing And Morth Specifications Clauses 1700, 2302 And 2304 R.c.c. Grade M 30 Supplying, Fitting, And Placing Hysd Bar Reinforcement In Superstructure Complete As Per Drawing And Morth Specifications Clauses 1009,1600 And 2302 Providing And Laying Cement Concrete Wearing Course M 30 Grade Including Reinforcement Complete As Per Drawing And Morth Specifications Clauses 1700 And 2702.2 Providing And Fixing 20 Mm Thick Compressible Fibre Board In Expansion Joint Complete As Per Drawing And Morth Specifications Clause 2604 Providing And Fillling Joint Sealing Compound As Per Drawings And Morth Specifications With Coarse Sand And 6 Per Cent Bitumen By Weight Clause 2604 Providing And Laying Filter Media With Granular Crushed Aggregates As Per Specification To A Thickness Of Not Less Than 600 Mm With Smaller Size Towards The Soil And Bigger Size Towards The Wall And Providing Over The Entire Surface Behind Abutment, Wing Wall, Return Wall To The Full Height, Compacted To Firm Condition Complete As Per Drawing And Morth Specification Clause 2204.6 & 2504.2.2 Backfilling Behind Abutment, Wing Wall And Return Wall Complete As Per Drawings & Morth Specification Clause 304.3.7 & 2204.6 Granular Material Dismantling Of Existing Structures Like Culverts, Bridges, Retaining Walls And Other Structure Comprising Of Stone Masonry, Including Disposal Of Unserviceable Material And Stacking The Serviceable Material With All Lift And Lead Of 1000 M As Per Morth Specification Clause 202. Rubble Stone Masonry In Cement Mortar Supply & Fixing Of Flood Gauge (water Gauge) As Per I.r.c. 67 Standard 200 Cm Long Fixed On Angle Iron Posts 50x50x6 Mm, 2.6 M. Long. Construction Of Embankment With Material Obtained From Borrow Pits Construction Of Embankment With Approved Material Obtained From Borrow Pits With A Lift Upto 1.5 M, Transporting To Site, Spreading, Grading To Required Slope And Compacting To Meet Requirement Of Tables 300-1 And 300-2 With A Lead Upto 50 M As Per Morth Specification Clause 305 Granular Sub-base With Close Graded Material (table:- 400-1) Plant Mix Method Providing Laying Spreading And Compacting Specified Graded Sand, Gravel (crushed Stone) As Per Table 400-1,400-2 Or Any Other Course Material As Per Design Mix, As Per Cbr In Sub Base Course Including Premixing The Material At Omc In Wet Mix Plant, Carriage Of Mixed Material Spreading In Uniform Layers With Motor Grader F.e Loader On A Prepared Base And Compacting With Vibratory Roller To Achieve Desired Density (as Per I.s.2720) Including All Material, Labor, Machinery, Lighting Guarding, Barricading And Maintenance Of Diversion Complete.[morth Specification : Clause 401]. By Mechanical Means. For Grading-ii Material Dry Lean Cement Concrete Construction Of Dry Lean Cement Concrete Sub- Base Over A Prepared Sub-grade With Coarse And Fine Aggregate Conforming To Is: 383, The Size Of Coarse Aggregate Not Exceeding 25 Mm, Aggregate Cement Ratio Not To Exceed 15:1, Aggregate Gradation After Blending To Be As Per Table 600-1, Cement Content Not To Be Less Than 150 Kg/ Cum, Optimum Moisture Content To Be Determined During Trial Length Construction, Concrete Strength Not To Be Less Than 10 Mpa At 7 Days, Mixed In A Batching Plant, Transported To Site, Laid With A Paver With Electronic Sensor, Compacting With 8-10 Tonnes Vibratory Roller, Finishing And Curing. Construction Of Un-reinforced , Plain Cement Concrete Pavement M30 (grade), Thickness As Per Design, Over A Prepared Sub Base, With 43/53 Grade Cement As Per Clause 602, Coarse And Fine Aggregates Conforming To Is:383, Maximum Size Of Coarse Aggregate Not Exceeding 31.5 Mm, Mixed In A In Fully Automatic Batching Plant And Transported To Site In Transit Mixer For Having Continuous Agitated Mixer, Manufactured As Per Approved Mix Design Including Pumping Of R.m.c. From Transit Mixer To Site Of Laying , With All Lead And Lift Including Cost Of Admixtures In Recommended Portion As Per Is 9103 To Accelerate/ Retard Setting Of Concrete, Improve Workability Without Impairing Strength And Durability As Per Direction Of Engineer In Charge Laid With A Fixed Form Paver (laying And Fixing Of 150 Micron Thick Polythene Film And Finished In Continuous Operation Including Provision Of Contraction And Expansion, Construction Joints, Applying Debonding Strips, Primer, Sealant Near Approaches To Bridge/culvert And Construction Joints, Admixtures As Approved, Curing Of Concrete Slabs For 14-days Using Water Finishing To Lines And Grade As Per Drawing And Morth Specification Clause 602 Including Vaccum Dewatering Process With All Required Equipments (dowel Bars Will Be Paid Seprately). Providing And Fixing Of Dowel Bars Of Mild Steel Confirming To Is : 432 Of Specified Length And Diameters As Per Morth Specification Irc 15 & 58 Including Cutting, Placing In Position Across Transverse Joint With Proper Spacing, Providing With Pvc Sleeve Complete As Per Drawing, Technical Specification And As Per Direction Of The Engineer-in-charge. Providing And Fixing Of Retro-reflectorised Cautionary, Mandatory And Informatory Sign As Per Irc:67 Made Of Encapsulated Lens Type Reflective Sheeting Vide Clause 801.3.1 Fixed Over Aluminium Sheeting, 1.5 Mm Thick Supported On A Mild Steel Angle Iron Post 75 Mm X 75 Mm X 6 Mm Firmly Fixed To The Ground By Means Of Properly Designed Foundation With M15 Grade Cement Concrete 450 Mm X 450 Mm X 600 Mm, 600 Mm Below Ground Level As Per Drawings And Morth Specification Clause 801 600 Mm X 450 Mm Rectangular Chhabra Gugor Road To Kadia-kotdi Till Daulatpur Near Kadia Village
Excavation For Structures Earthwork In Excavation For Structures As Per Drawing And Morth Specifications Clause 304.1 Including Setting Out, Construction Of Shoring And Bracing, Removal Of Stumps And Other Deleterious Material And Disposal Upto A Lead Of 50 M, Dressing Of Sides And Bottom And Backfilling In Trenches With Excavated Suitable Material. Ordinary Soil Upto 3 M Depth Providing Concrete For Plain/reinforced Concrete In Open Foundations Complete As Per Drawings And Morth Specifications Clause 1702, 1703, 2102 & 2104 P.c.c Grade M 10 Nominal Mix 1:3:6 Providing Concrete For Plain/reinforced Concrete In Open Foundations Complete As Per Drawings And Morth Specifications Clause 1702, 1703, 2102 & 2104 R.c.c Grade M 20 Supplying, Fitting And Placing Hysd Bar Reinforcement In Foundation Complete As Per Drawings And Morth Specifications Clauses 1009,1600 And 2102 Plain/reinforced Cement Concrete In Substructure Complete As Per Drawings And Morth Specification Clauses 1700 And 2200 For Height Upto 5 M R.c.c Grade M 20 Plain/reinforced Cement Concrete In Substructure Complete As Per Drawings And Morth Specification Clauses 1700 And 2200 For Height Upto 5 M R.c.c. Grade M 25 Supplying, Fitting And Placing Hysd Bar Reinforcement (fe 415) In Substructrue Complete As Per Drawings And Morth Specification Clauses 1009,1600 & 2202 Providing Weepholes In Brick Masonry/stone Masonry, Plain/reinforced Concrete Abutment, Wing Wall, Return Wall With 100 Mm Dia Ac Pipe Extending Through The Full Width Of The Structures With Slope Of 1(v):20(h) Towards Drawing Face Complete As Per Drawing And Morth Specification Clauses 1409, 2204.4, 2206.4 & 2706 Providing And Laying Reinforced Cement Concrete In Superstructure As Per Drawing And Morth Specifications Clauses 1700, 2302 And 2304 R.c.c. Grade M 30 Supplying, Fitting, And Placing Hysd Bar Reinforcement In Superstructure Complete As Per Drawing And Morth Specifications Clauses 1009,1600 And 2302 Providing And Laying Cement Concrete Wearing Course M 30 Grade Including Reinforcement Complete As Per Drawing And Morth Specifications Clauses 1700 And 2702.2 Providing And Fixing 20 Mm Thick Compressible Fibre Board In Expansion Joint Complete As Per Drawing And Morth Specifications Clause 2604 Providing And Fillling Joint Sealing Compound As Per Drawings And Morth Specifications With Coarse Sand And 6 Per Cent Bitumen By Weight Clause 2604 Drainage Spouts Complete As Per Drawing And Morth Specifications Clause 2705 Providing And Laying Filter Media With Granular Crushed Aggregates As Per Specification To A Thickness Of Not Less Than 600 Mm With Smaller Size Towards The Soil And Bigger Size Towards The Wall And Providing Over The Entire Surface Behind Abutment, Wing Wall, Return Wall To The Full Height, Compacted To Firm Condition Complete As Per Drawing And Morth Specification Clause 2204.6 & 2504.2.2 Backfilling Behind Abutment, Wing Wall And Return Wall Complete As Per Drawings & Morth Specification Clause 304.3.7 & 2204.6 Granular Material Dismantling Of Existing Structures Like Culverts, Bridges, Retaining Walls And Other Structure Comprising Of Stone Masonry, Including Disposal Of Unserviceable Material And Stacking The Serviceable Material With All Lift And Lead Of 1000 M As Per Morth Specification Clause 202. Rubble Stone Masonry In Cement Mortar Construction Of Embankment With Material Obtained From Borrow Pits Construction Of Embankment With Approved Material Obtained From Borrow Pits With A Lift Upto 1.5 M, Transporting To Site, Spreading, Grading To Required Slope And Compacting To Meet Requirement Of Tables 300-1 And 300-2 With A Lead Upto 50 M As Per Morth Specification Clause 305.3 Providing Laying Spreading And Compacting Specified Graded Sand, Gravel (crushed Stone) As Per Table 400-1,400-2 Or Any Other Course Material As Per Design Mix, As Per Cbr In Sub Base Course Including Premixing The Material At Omc In Wet Mix Plant, Carriage Of Mixed Material Spreading In Uniform Layers With Motor Grader F.e Loader On A Prepared Base And Compacting With Vibratory Roller To Achieve Desired Density (as Per I.s.2720) Including All Material, Labor, Machinery, Lighting Guarding, Barricading And Maintenance Of Diversion Complete.[morth Specification : Clause 401]. By Mechanical Means. For Grading-ii Material Construction Of Dry Lean Cement Concrete Sub- Base Over A Prepared Sub-grade With Coarse And Fine Aggregate Conforming To Is: 383, The Size Of Coarse Aggregate Not Exceeding 25 Mm, Aggregate Cement Ratio Not To Exceed 15:1, Aggregate Gradation After Blending To Be As Per Table 600-1, Cement Content Not To Be Less Than 150 Kg/ Cum, Optimum Moisture Content To Be Determined During Trial Length Construction, Concrete Strength Not To Be Less Than 10 Mpa At 7 Days, Mixed In A Batching Plant, Transported To Site, Laid With A Paver With Electronic Sensor, Compacting With 8-10 Tonnes Vibratory Roller, Finishing And Curing. Construction Of Un-reinforced , Plain Cement Concrete Pavement M30 (grade), Thickness As Per Design, Over A Prepared Sub Base, With 43/53 Grade Cement As Per Clause 602, Coarse And Fine Aggregates Conforming To Is:383, Maximum Size Of Coarse Aggregate Not Exceeding 31.5 Mm, Mixed In A In Fully Automatic Batching Plant And Transported To Site In Transit Mixer For Having Continuous Agitated Mixer, Manufactured As Per Approved Mix Design Including Pumping Of R.m.c. From Transit Mixer To Site Of Laying , With All Lead And Lift Including Cost Of Admixtures In Recommended Portion As Per Is 9103 To Accelerate/ Retard Setting Of Concrete, Improve Workability Without Impairing Strength And Durability As Per Direction Of Engineer In Charge Laid With A Fixed Form Paver (laying And Fixing Of 150 Micron Thick Polythene Film And Finished In Continuous Operation Including Provision Of Contraction And Expansion, Construction Joints, Applying Debonding Strips, Primer, Sealant Near Approaches To Bridge/culvert And Construction Joints, Admixtures As Approved, Curing Of Concrete Slabs For 14-days Using Water Finishing To Lines And Grade As Per Drawing And Morth Specification Clause 602 Including Vaccum Dewatering Process With All Required Equipments (dowel Bars Will Be Paid Seprately). Providing And Fixing Of Dowel Bars Of Mild Steel Confirming To Is : 432 Of Specified Length And Diameters As Per Morth Specification Irc 15 & 58 Including Cutting, Placing In Position Across Transverse Joint With Proper Spacing, Providing With Pvc Sleeve Complete As Per Drawing, Technical Specification And As Per Direction Of The Engineer-in-charge. Supply & Fixing Of Flood Gauge (water Gauge) As Per I.r.c. 67 Standard 200 Cm Long Fixed On Angle Iron Posts 50x50x6 Mm, 2.6 M Long Providing And Fixing Of Retro-reflectorised Cautionary, Mandatory And Informatory Sign As Per Irc:67 Made Of Encapsulated Lens Type Reflective Sheeting Vide Clause 801.3.1 Fixed Over Aluminium Sheeting, 1.5 Mm Thick Supported On A Mild Steel Angle Iron Post 75 Mm X 75 Mm X 6 Mm Firmly Fixed To The Ground By Means Of Properly Designed Foundation With M15 Grade Cement Concrete 450 Mm X 450 Mm X 600 Mm, 600 Mm Below Ground Level As Per Drawings And Morth Specification Clause 801 800 Mm X 600 Mm Rectangular Painting Two Coats Including Primer Coat After Filling The Surface With Synthetic Enamel Paint In All Shades On New, Plastered / Concrete Surfaces As Per Drawing And Morth Specification Clause 801 Bapacha To Dhingrari Via Phaliya Via Kadiyahat Km. 6/550, 9/750
Providing Laying Spreading And Compacting Specified Graded Sand, Gravel (crushed Stone) As Per Table 400-1,400-2 Or Any Other Course Material As Per Design Mix, As Per Cbr In Sub Base Course Including Premixing The Material At Omc In Wet Mix Plant, Carriage Of Mixed Material Spreading In Uniform Layers With Motor Grader F.e Loader On A Prepared Base And Compacting With Vibratory Roller To Achieve Desired Density (as Per I.s.2720) Including All Material, Labor, Machinery, Lighting Guarding, Barricading And Maintenance Of Diversion Complete.[morth Specification : Clause 401]. By Mechanical Means. For Grading-ii Material Construction Of Dry Lean Cement Concrete Sub- Base Over A Prepared Sub-grade With Coarse And Fine Aggregate Conforming To Is: 383, The Size Of Coarse Aggregate Not Exceeding 25 Mm, Aggregate Cement Ratio Not To Exceed 15:1, Aggregate Gradation After Blending To Be As Per Table 600-1, Cement Content Not To Be Less Than 150 Kg/ Cum, Optimum Moisture Content To Be Determined During Trial Length Construction, Concrete Strength Not To Be Less Than 10 Mpa At 7 Days, Mixed In A Batching Plant, Transported To Site, Laid With A Paver With Electronic Sensor, Compacting With 8-10 Tonnes Vibratory Roller, Finishing And Curing. Construction Of Un-reinforced , Plain Cement Concrete Pavement M30 (grade), Thickness As Per Design, Over A Prepared Sub Base, With 43/53 Grade Cement As Per Clause 602, Coarse And Fine Aggregates Conforming To Is:383, Maximum Size Of Coarse Aggregate Not Exceeding 31.5 Mm, Mixed In A In Fully Automatic Batching Plant And Transported To Site In Transit Mixer For Having Continuous Agitated Mixer, Manufactured As Per Approved Mix Design Including Pumping Of R.m.c. From Transit Mixer To Site Of Laying , With All Lead And Lift Including Cost Of Admixtures In Recommended Portion As Per Is 9103 To Accelerate/ Retard Setting Of Concrete, Improve Workability Without Impairing Strength And Durability As Per Direction Of Engineer In Charge Laid With A Fixed Form Paver (laying And Fixing Of 150 Micron Thick Polythene Film And Finished In Continuous Operation Including Provision Of Contraction And Expansion, Construction Joints, Applying Debonding Strips, Primer, Sealant Near Approaches To Bridge/culvert And Construction Joints, Admixtures As Approved, Curing Of Concrete Slabs For 14-days Using Water Finishing To Lines And Grade As Per Drawing And Morth Specification Clause 602 Including Vaccum Dewatering Process With All Required Equipments (dowel Bars Will Be Paid Seprately). Providing And Fixing Of Dowel Bars Of Mild Steel Confirming To Is : 432 Of Specified Length And Diameters As Per Morth Specification Irc 15 & 58 Including Cutting, Placing In Position Across Transverse Joint With Proper Spacing, Providing With Pvc Sleeve Complete As Per Drawing, Technical Specification And As Per Direction Of The Engineer-in-charge. Construction Of Embankment With Approved Material Obtained From Borrow Pits With A Lift Upto 1.5 M, Transporting To Site, Spreading, Grading To Required Slope And Compacting To Meet Requirement Of Tables 300-1 And 300-2 With A Lead Upto 50 M As Per Morth Specification Clause 305.3 Supply & Fixing Of Flood Gauge (water Gauge) As Per I.r.c. 67 Standard 200 Cm Long Fixed On Angle Iron Posts 50x50x6 Mm, 2.6 M Long Providing And Fixing Of Retro-reflectorised Cautionary, Mandatory And Informatory Sign As Per Irc:67 Made Of Encapsulated Lens Type Reflective Sheeting Vide Clause 801.3.1 Fixed Over Aluminium Sheeting, 1.5 Mm Thick Supported On A Mild Steel Angle Iron Post 75 Mm X 75 Mm X 6 Mm Firmly Fixed To The Ground By Means Of Properly Designed Foundation With M15 Grade Cement Concrete 450 Mm X 450 Mm X 600 Mm, 600 Mm Below Ground Level As Per Drawings And Morth Specification Clause 801 800 Mm X 600 Mm Rectangular Painting Two Coats Including Primer Coat After Filling The Surface With Synthetic Enamel Paint In All Shades On New, Plastered / Concrete Surfaces As Per Drawing And Morth Specification Clause 801 Excavation For Structures Earthwork In Excavation For Structures As Per Drawing And Morth Specifications Clause 304.1 Including Setting Out, Construction Of Shoring And Bracing, Removal Of Stumps And Other Deleterious Material And Disposal Upto A Lead Of 50 M, Dressing Of Sides And Bottom And Backfilling In Trenches With Excavated Suitable Material. Ordinary Soil Upto 3 M Depth Providing Concrete For Plain/reinforced Concrete In Open Foundations Complete As Per Drawings And Morth Specifications Clause 1702, 1703, 2102 & 2104 P.c.c Grade M 10 Nominal Mix 1:3:6 Providing Concrete For Plain/reinforced Concrete In Open Foundations Complete As Per Drawings And Morth Specifications Clause 1702, 1703, 2102 & 2104 R.c.c Grade M 20 Supplying, Fitting And Placing Hysd Bar Reinforcement In Foundation Complete As Per Drawings And Morth Specifications Clauses 1009,1600 And 2102 Providing And Laying Reinforced Cement Concrete Pipe Np3 For Culverts On First Class Bedding Of Granular Material In Single Row Including Fixing Collar With Cement Mortar 1:2 But Excluding Excavation, Protection Works, Backfilling, Concrete And Masonry Works In Head Walls And Parapets Clause 2905. 1000 Mm Dia Bheelwada Neecha To Bhilwara Uncha Km. 0/500, 0/700, 1/200
Gem Bids For Pvc Sleeve Suitable For 1.5 Sq Mm Wire Size As Perspec. Am54364, Rev. 00
Gem Bids For Bolt Metalic Black St Hex Hd, Nut Plane Hex Black, Toolsteel Carbon Round 10mm, Pin Cutter Split 2 5mm, Hosepipe, Compressed Gas Nitrogen, Cable 15, 12 Pin Plug, Rivit 90 Steel 6x50mm, Insulation Tape Electrical Cottonself A, Pvc Sleeve 3id 25mm Long Green, Pvc Sleeve 3id25mm Long Violet, Pipe L 1850, Bulb 24v 5w Cap Ba
Gem Bids For Main Cable Assy 2m Anr Dch , Cable Assy Between Earcups Anr Dch , Seal Screw 14 40x 5obliqe16 , Scrw 4 40x 1obliqe4 Crsblk , Screw 4 40x 5obliqe16 , Elb I Boom Microphone Assy Anr Dch , Conn Housing 8p 1point25 Mm , Pvc Sleeve Blk Id
Gem Bids For Wiring, Electrical Cable Copper Multi Conductor Pvc Insulated Dcwire Single Core Red Bare Copper , Brass Ring Tongueterminal Solder Type Tin Coated For 10 Sq Mm Cable 10 Point5 Mm Id, Brass Ring Tongue Terminal Solder Type Tin Coatedfor 10 Sq Mm Cable 6 Point 5 Mm Id, Cable Conduit Pvcflexible Black 08 Mm Id, Hs Sleeve Black 12 By 6 Mm, Insulating Sleeve Pvc White 12 Mm Dia, Solder Soft Comma16 Swg Sn 63 Percent Pb 37 Percent, Solder Flux, Plasticcover Comma 80 Microns 18 X 12, Permanent Marker Penblack
Supply Of Fire Retardant Pvc Sleeve Of 42 Mm.
Supply Of Pvc Sleeve Bore Dia 8mm With.
