"नये भारत का नया Tender Portal"
Supply Of S.s.inlay Support Plate Size 1250x150x2 Mm.
Supply of Contactor With Surge Suppressor For 60Kva Transformer, Rated Current: 95A, Rated Voltage: 690V Ac, 50/60Hz, Main Pole: 04 Nos., Aux. Contact: 2No + 1Nc, Control Circuit Voltage: 230V Ac +/-30% 168-300V Ac With Plate & Rail Mounting Support Confirming To Standard Iec/En 60947. Place Of Installation: S1k44 In Switch Board Cabinet Of Lhb Ac Coach As Per Rdso Spec. No. Rdso/Pe/Spec/Ac/0184-2015 Rev.1 Or Lat. And Rdso Ltr. No. El/7.1.108/Mssbc Dt.: 17-09-21. Make As Per Bom Are Abb Cat. No.Af 116B-40, Schneider Cat. No. Lc1d1150046m5+La4da2u Or Any Other Rdso Approved Make..
Supply Of Wear Plate Liner For Yoke Pin Support Plate As Per As Per Drawing No. Wa/bd- 4462 Item No. Part-a Alt. 8 & Specification No.-wd-70 Bd-10 Rev.-4. Is:3885 Part-1 Grade Iv. Hardness 262-302 Bhn..
Gem Bids For Spanner, Spanner 39X5 5X220 Hw 066 01 21, Disc Hw 080 09Fully M Cd Item, Plate Hw 250 71 Fully M Cd Item, Round D20x1200 Hw 277 13 With Matl, Screw Hw 06303, Throttling Screw M16x30 Var 03 Hw 100, Anglehw 292 20 Fully M Cd Item, Angle Var 00 Hw 292, Angle Var 01 Hw 292, Square Nut Hw 292 12, Guidecolumn Var 03 L 1250 Hw 291, Transport Ring Hw263 52, Transport Ring Hw 263 63, Ring Hw 096 02, Guide Column Var 02 L 850 Hw 066 03, Ring Hw 250 72Fully M Cd Item, Hex Bolt M36 Hw 063 05, Guidecolumn Var 00 L 675 Hw 066 03, Po Bolt M30x160 L850 Hw 072, Hexagonal Cap Screw L 160 Var 04, Hexbolt M42 Hw 396, Support Plate Hw 396 52
Gem Bids For Machining, U Channel For Pot Shell, Pot Hood Slab Supportfor Pot Shell, Clit For Laddle, Shaft Lock Device Nkmrot Table L 115 Mm, Shaft Lock Device Rotary Tablenkm 266mm, Nkm Rotary Table Guide Plates Fortrans, Cuting Head Side Outer Flange Of Nkm, Cutting Head Side Inner Flange Of Nkm, Spacers Ofcutting Head Of Nkm, Cover Cutting Head Side Brgof New Ccm, Cutting Shaft Drive End Side Brgcover, Slab Support Plate
Supply Of Hexagon Head Bolt Size M30 X 160 Property Class 8.8 Zinc Plated As Per Is 1364/2002 For Tm Support Plate. Make And Property Class Must Be Embossed On Hardware. Clw Item Id: 2100143..
Drilling Of Condenser Tube Support Platetsp To Drg No-01600040068 Rev 01 And As Per Technical Annexure- A. Undrilled Tube Support Plates Shall Be Issued In Lots01 Lot-04 Nos Tsp. Steam Washable Should Be Applied On Each Tube Support Plate After D
Gem Bids For 3D, Letter, Logo, Special Character, Base Plate, Iron Angle, Support Angle, Squire Pipe, Acp Board
Gem Bids For Top Cover Assembly Rh Side Cover Plate Assembly Top Cover Assembly Rear End Plate Assembly Forward End Bracket Assembly Rear End Plate Assembly Inclined Support Assembly Bottom Access Cover Assembly 1 To 2 Nose Cone Fwd Shell Assembly Sup. Bkt.channel Eo Pod Floor Side Bot Skin 9 To 9a Lh Side Bot Skin 9 To 9a Rh Aft Box Assem. Fin Box Assembly Front Emru Fairing Outboard Lh Front Emru Fairing Outboard Rh Rear Fairing Root Assy Lh Rear Fairing Root Assy Rh Rear Fairing Tip And Rib Assy Lh Rear Fairing Tip And Rib Assy Rh Box Assembly Rhs
Gem Bids For Crank Casting , Angle Plate Casting , Damper Support Casting
